Intended for attaching of wire rope where switching often occur, e.g. blocks of mobilecranes, or to be able to adjust the length of the wire rope. See recommended assembly to get correct results.
The wedge socket is delivered complete with wedge, pin and cotterpin.
2 surface finishes available:
Model OWS P : blue painted.
Model OWS PGAL : Hot dipped galvanized.
Model OWS 0.25 and OWS 0.5 only standard available in hot dipped galvanized.
Material: Quenched and tempered cast steelMarking: Size, wire rope diameter and batch or serial number.Temperature range: -40°C to +100°C - Use at higher temperatures possible with reduction of WLL.Finish: Blue painting or hot dipped galvanizedNote: The efficiency of a 6 and 8 strand wire rope/wedge socket connection is 80% of the minimum breaking load of the wire but limited to the minimum breaking load of the socket (MBL).
A revolutianary evolution of the Fast Connector Socket. This socket line has the smallest connector diameter available inthe market today, and still meets the respective EN standards. It has been designed to go through the smallest spaces in a crane reeving system.
This unique patent pending design allows refitting by pouring in the field, saving valuable down time compared to swaging techniques.
The standard finish of our sockets is blue. Hot dipped galvanized is also available.
Material: Quenched and tempered cast steel.
General: - Standard Reeve Crane Blocks may be used on a wide variety of land based cranes such as mobile and crawler cranes. They are an excellent choice where frequent easy block change is not a required main feature, or lifting height is limited.- Double sealed maintenance free roller bearings.- Design Factor of Safety of 4:1.- Forged high tensile steel DIN hooks.- Ductile iron sheaves, featuring graphite lubricated groove.- High impact resistant side plates.- Operational temperature range -40 up to +80°C.- Lubrication on hook suspension.- Short design for increased lifting height.- Safety latch with locking pin.- C3M finish in signal yellow.
Options: - Double hook.- Double hook with shackle hole.- Quad hook.- Shackle stud eye.
Important:Inquiries for custom versions are welcome!
Dimensional tolerances depend on the manufacturing techniques applied and are different between machined components (pins) and cast components (socket bodies and wedges).
All sockets are provided with an EN 10204-2.1 declaration of conformity, EN 10204-3.1 material certificate and can be provided with a 2006/42/EC declaration where applicable.
Also surface finish e.g. hot dip galvanizing may add to the overall thickness and fork distance.
Material: Quenched and tempered cast steel.Finish: Hot dipped galvanized.
The tailgrip open wedge socket with pin is a fast detachable socket. It is suitable for usage in a sub-zero temperature environment
Basket and wedge in quenched and tempered cast steel. Wedge and basket are designed for easy installation and optimal wire rope efficiency and with the added benefit to terminate the tail to the wedge itself.
Material: Quenched and tempered cast steelMarking: According to standard, CE-marked, All parts are fully traceable to their certificate by batch or serial number marked on each component.Temperature range: - 40°C to + 110°C - Use at higher temperatures possible with reduction of WLL.Finish: Blue painting or hot dipped galvanizedStandard: EN 10204 Warning: The efficiency of a 6 and 8 strand wire rope/wedge socket connection is 80% of the minimum breaking load of the wire but limited to the minimum breaking load of the socket (MBL).
Tailgrip open wedge socket with bolt and nut.
It is suitable for usage in a sub-zero temperature environment
Basket and wedge in quenched and tempered cast steel. Wedge and basket are designed for easy installation and optimal wire rope efficiency and with the added benefit to terminate the tail to the wedge itself.
Material: Quenched and tempered cast steelMarking: According to standard, CE-marked, All parts are fully traceable to their certificate by batch or serial number marked on each component.Temperature range: - 40°C to + 110°C - Use at higher temperatures possible with reduction of WLL.Finish: Blue painting or hot dipped galvanizedStandard: EN 10204 Warning: The efficiency of a 6 and 8 strand wire rope/wedge socket connection is 80% of the minimum breaking load of the wire but limited to the minimum breaking load of the socket (MBL).
General: - Standard Reeve Crane Blocks may be used on a wide variety of land based cranes such as mobile and crawler cranes. They are an excellent choice where frequent easy block change is not a required main feature, or lifting height is limited.- Double sealed maintenance free roller bearings.- Design Factor of Safety of 4:1.- Forged high tensile steel DIN hooks.- Ductile iron sheaves, featuring graphite lubricated groove.- High impact resistant side plates.- Operational temperature range -40 up to +80°C.- Lubrication on hook suspension.- Short design for increased lifting height.- Safety latch with locking pin.- C3M finish in signal yellow.
Options: - Double hook.- Double hook with shackle hole.- Quad hook.- Shackle stud eye.
Important:Inquiries for custom versions are welcome!
General: - Generally to ASTM F 1145-92- Standard hot dip galvanized. - Factory supplied with lock nuts. - Proof load 2.5 x WLL. - Straight or in-line pull only. - Drop forged high tensile steel. - MBL equals or over 5x WLL
Forged clevis fittings with bolt, nut and cutterpin for fast connection of steel wire rope. Can be used to terminate all constructions of wire rope including high performance ropes, anti-rotation ropes and standard 6 strand ropes.
The connector has to be moulded/casted on the steel wire rope with wirelock resin.
Features: Designed for use with mobile cranes.Material: Quenched and tempered cast steel.Finish: Blue painted or hot dip galvanized.Warning: Compare the spelter's and the wire rope's minimum breaking load.
Quenched and tempered cast steel range with mechanical values (Charpy-V > 42 Joule / -20°C) for tough and low temperature use. For wire rope diameter 6-200mm. Pin scured by cotter pin or bolt, nut and cotter.
Optional is a flange connection for use with a bend stifferener.
All spelter sockets have a 100% efficiency on wire rope MBL.
Standard: EN 10204-2.1 declaration of conformity / EN 10204-3.1 material certificate.
Options:
Hot dip galvanized.
pin secured (modelnr. P) or bolt and nut (modelnr. B)
Material: Quenched and tempered cast steel.Finish: Blue painted or hot dip galvanized.
Intended for attaching of wire rope where switching often occur, e.g. blocks of mobilecranes, or to be able to adjust the length of the wire rope. See recommended assembly to get correct results. The wedge socket is delivered complete.
Marking house and wedge: Wire ø mm.
Material: Cast alloy steel with high mechanical properties.Temperature range: - 40°C to + 110°C - Use at higher temperatures possible with reduction of WLL.Finish: Blue painted (P) or hot dip galvanized (G).Note: The efficiency of a 6 and 8 strand wire rope/wedge socket connection is 80% of the minimum breaking load of the wire but limited to the minimum breaking load of the socket (MBL).
Quenched and tempered cast steel range steel wire rope sockets for embedment with cast compound with mechanical values (Charpy-V > 42 Joule /-20°C) for tough and low temperature use. For wire rope diameter 6 - 203 mm (1/4” - 8”).
2 surface finishes available:
Model OSS P: blue painted. (OSS 196 until OSS 100 only Hot dipped galvanized)
Model OSS P.GAL: Hot dipped galvanized.
Features:
Pin securing by cotter pin.
All spelter sockets have a 100% efficiency.
Also available with pin + bolt ( type OSS B )
Material: Quenched and tempered cast steelMarking: CE-marked, Size, wire rope diameter and batch or serial number.Temperature range: From - 40°C up to +110°C - 100% capacity range.Finish: OSS P: blue painted - OSS PGAL : Hot dipped galvanized.Note: For intermediate rope diameter select fittings with nearest following size. Warning: Compare the spelter's and the wire rope's minimum breaking load.
General: - Standard Reeve Crane Blocks may be used on a wide variety of land based cranes such as mobile and crawler cranes. They are an excellent choice where frequent easy block change is not a required main feature, or lifting height is limited.- Double sealed maintenance free roller bearings.- Design Factor of Safety of 4:1.- Forged high tensile steel DIN hooks.- Ductile iron sheaves, featuring graphite lubricated groove.- High impact resistant side plates.- Operational temperature range -40 up to +80°C.- Lubrication on hook suspension.- Short design for increased lifting height.- Safety latch with locking pin.- C3M finish in signal yellow.
Options: - Double hook.- Double hook with shackle hole.- Quad hook.- Shackle stud eye.
Important:
Inquiries for custom versions are welcome!
General: Besides being an integral part of blocks, sheaves are also used in a wide variety of applications, not only limited to cranes. Ropeblock has developed a standard line of sheaves that are used for most wireropes. Standard production is cast ductile iron with graphite lubricated grooves, however, cast steel, nylon and welded fabrication is also possible.Some key benefits of ropeblock sheaves:- Optimal groove opening angle coping with fleet angle problems.- Wide range of bearing options to meet your specific requirement.- Self-lubricating "graphite-rich" grooves to promote wire rope longevity.- Optimally designed to reduce fatigue.Options:- Finish depending on application.- Different shaft sizes possible.- Groove may be adjusted to other wire rope diameters.
Forged clevis fittings with bolt, nut and cutterpin for fast connection of steel wire rope. Can be used to terminate all constructions of wire rope including high performance ropes, anti-rotation ropes and standard 6 strand ropes.
The connector has to be moulded / casted on the steel wire rope with wirelock resin.
Features: Designed for use with mobile cranes.Material: Quenched and tempered cast steel.Finish: Blue painted (P) or hot dip galvanized (G).Warning: Compare the spelter's and the wire rope's minimum breaking load.
The Ropeblock closed spelter socket CSS designed with mechanical values (Charpy-V > 42 joule / - 20° C) for though and low temperature use.
All sockets have a 100% efficency on the MBL of the steel wire rope but are limited to the MBL of the socket.
The CSS sockets are Type Approved by DNV and Lloyd’s Register.
CSS 296 until CSS 201 only available with hot dipped galvanized finish.
Material: Quenched and tempered cast steel.Marking: CE-markedTemperature range: - 40°C to + 110°C - Use at higher temperatures possible with reduction of WLL.Finish: Hot dipped Galvanized (G) or painted blue (P).
Intended for attaching of wire rope where switching often occur, e.g. blocks of mobilecranes, or to be able to adjust the length of the wire rope. See recommended assembly to get correct results.
The wedge socket is delivered complete with wedge, bolt, nut and cotterpin.
2 surface finishes available:
Model OWS B: blue painted.
Model OWS BGAL: Hot dipped galvanized.
Model OWS 0.25 and OWS 0.5 only standard available in hot dipped galvanized.
Material: Quenched and tempered cast steel.Marking: Size, wire rope diameter and batch or serial number.Temperature range: -40°C to + 110°C - Use at higher temperatures possible with reduction of WLL.Finish: Blue painting or hot dipped galvanized.Note: The efficiency of a 6 and 8 strand wire rope/wedge socket connection is 80% of the minimum breaking load of the wire but limited to the minimum breaking load of the socket (MBL).
General: - Standard hot dip galvanized. - Factory supplied with lock nuts. - Proof load 2.5 x WLL. - Straight or in-line pull only. - Drop forged high tensile steel. - MBL equals 5x WLL.
General: - Standard Reeve Crane Blocks may be used on a wide variety of land based cranes such as mobile and crawler cranes. They are an excellent choice where frequent block change is required.- Double sealed maintenance free roller bearings.- Design Factor of Safety of 4:1.- Forged high tensile steel DIN hooks.- Ductile iron sheaves, featuring graphite lubricated groove.- High impact resistant side plates.- Operational temperature range -40 up to +80°C.- Lubrication on hook suspension.- 4 or 8 point hook locking device.- Fast reeve guide for fast reeving.- Safety latch with locking pin.- C3M finish in signal yellow with black striping.
Options: - Double hook.- Double hook with shackle hole.- Quad hook.- Shackle stud eye.
Important:Inquiries for custom versions are welcome!
Quenched and tempered cast steel range steel wire rope sockets for embedment with cast compound with mechanical values (Charpy-V > 42 Joule /-20°C) for tough and low temperature use. For wire rope diameter 6 - 203 mm (1/4” - 8”).
2 surface finishes available:
Model OSS B: blue painted. (OSS 196 - OSS 100 only hot dipped galvanized)
Model OSS B.GAL: Hot dipped galvanized.
Features:
Bolt securing by nut and cotter pin.
All spelter sockets have a 100% efficiency.
Also avaiable with pin + cotter pin ( type OSS P )
Material: Quenched and tempered cast steelMarking: Size, wire rope diameter and batch or serial number.Temperature range: From - 40°C up to +110°C - 100% capacity range.Finish: OSS B blue painted - OSS BGALV : Hot dipped galvanized.Note: For intermediate rope diameter select fittings with nearest following size. Warning: Compare the spelter's and the wire rope's minimum breaking load.
General: A revolutianary evolution of the Fast Connector Socket. This socket line has the smallest connector diameter available inthe market today, and still meets the respective EN standards. It has been designed to go through the smallest spaces in a crane reeving system.
This unique patent pending design allows refitting by pouring in the field, saving valuable down time compared to swaging techniques.
The standard finish of our sockets is blue. Hot dipped galvanized is also available.
Material: Quenched and tempered cast steel.