Beam Clamp - IPBK10
918.71 €*
WLL:
1
General: The IPBK10 beam clamp is used for lifting, transferring and stacking HBeams. A ring-center hoist eye allows for the beam flange to remain vertical. This series of clamps can be used in vertical and horizontal moving, transferring and stacking of different types of structural designs, such as H-Beams, angles, etc, depending on the application desired.
Features:
• Available in capacities of 0.5 thru 4 metric tons.
• Jaw openings available: 5 to 28mm
• Welded alloy steel body for strength and smaller size. Forged alloy components, where required.
• Individually Proof Tested to 2 times the Working Load Limit with certification.
• User manual with test certificate is included with each clamp.
• Maintenance and repair kits are available.
• For use with materials with a plate surface hardness to 279HV10, only 5% min WLL is needed.
• All sizes are RFID EQUIPPED.
Material: Alloy steel.Marking: According to standard, CE-markedStandard: EN 13155 Warning: A minimum load of 10% of the WLL is required.
Beam Clamp - IPBHZ
851.79 €*
WLL:
0.75
General:
The IPBHZ beam clamp is used for horizontal lifting and transferring of steel beams. The base is slotted to allow the clamps to be used from end of beams as well as from the flange. This series of clamps can be used in vertical and horizontal moving, transferring and stacking of different types of structural designs, such as I-Beams, H-beams, angles, etc, depending on the application desired.
Features:
• Available in capacities of .75 thru 12 metric tons.
• Wide variety of jaw openings available from 75 to 40 mm.
• Welded alloy steel body for strength and smaller size. Forged alloy components, where required.
• Individually Proof Tested to 2 times the Working Load Limit with certification.
• Maintenance and repair kits are available.
• All sizes are RFID EQUIPPED.
Material: Alloy steel.Marking: According to standard, CE-markedStandard: EN 13155 Warning: A minimum load of 10% of the WLL is required.
Beam Clamp IPSTARTEC11
1,204.49 €*
WLL:
1.5
General:
The IPSTARTEC11 beam clamp has been specially developed for lifting with the body in vertical position, controlled tilting, transportation and stacking of steel “H” and “I” profiles. By placing the chain guide in the appropriate position, it is easy to switch from lifting to tilting and back again, which shifts the center of gravity.
Features:
• Available in capacities of 1.5 and 2.5 metric tons.
• Jaw openings available: 6 to 20mm.
• Welded alloy steel body for strength and smaller size. Forged alloy components, where required.
• Individually Proof Tested to 2 times the Working Load Limit with certification.
• User manual with test certificate is included with each clamp.
• Maintenance and repair kits are available.
• All sizes are RFID EQUIPPED.
Features: Material: Alloy steel.Marking: According to standard, CE-markedStandard: EN 13155
Screw Pin Sling Shackle Crosby S-253
50.60 €*
WLL:
3.25
The Crosby S-253 top sling is designed to connect slings to steel fittings.
Meets or exceeds all requirements of ASME B30.26 including identification, ductility, design factor, proof load and temperature requirements. Importantly, these shackles meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
Material: All alloy construction.Marking: According to standard, CE-marked, Each shackle has a Product Identification Code (PIC) for material traceability along with a Working Load Limit and the name Crosby forged into it.Standard: EN 13889 Safety factor: 5:1
Beam Clamp - IPTKW
500.93 €*
WLL:
2
General:
The IPTKW series beam clamp is suitable for use as a temporary tackle eye for a beam and it is an economy version of the IPTK model.
Features:
• Available in capacities of 2 thru 5 metric tons.
• Wide variety of jaw openings available: 75 to 350 mm.
• Welded alloy steel body for strength and smaller size. Forged alloy components, where required.
• Individually Proof Tested to 2 times the Working Load Limit with certification.
• User manual with test certificate is included with each clamp.
• Maintenance and repair kits are available.
• All sizes are RFID EQUIPPED.
Material: Alloy steelMarking: According to standard, CE-markedStandard: EN 13155
Weldless Sling Links G-341
0.00 €*
Chain diameter:
16
|
WLL:
1.91
Material: Forged carbon steel - Quenched & TemperedMarking: CE-markedFinish: GalvanizedSafety factor: 6:1
Button Spelter Sockets, Crosby, SB-427
666.29 €*
MBL:
27
|
Rope Ø range:
16
Available in six sizes from 13 mm - 38 mm.
Button Spelter terminations have a 100% efficiency rating, based on the catalog strength of the wire rope.
Designed for use with mobile cranes. Can be used to terminate high performance, rotation resistant ropes, and standard 6 strand ropes.
Easy to install assembly utilizes Crosby WIRELOCK® socketing compound.
Sockets and buttons are re-usable.
Replacement buttons and sockets are available.
Locking feature available to prevent rotation of rope.
Button contains cap with eye that can be attached to, and used to pull, rope during reeving process.
Manufactured to the requirements of API-2C.
Vertical Lifting Clamps Non Marring- IPNM10 series
1,493.14 €*
WLL:
0.5
General:
The IPNM10 series vertical lifting clamps are used for lifting, turning, moving or vertical transfer of sheet, plates, or fabrications from horizontal to vertical and down to horizontal (180°) as needed without marring the surface of the material. Materials such as aluminum, stainless steel, painted materials, aircraft skins, composite material, glass, plastic, etc., can be lifted without marring or scratching the material surface. Available in a variety of models:
IPNM10(N) - standard model.
IPNM10P - Equiped with protection cap. Reduces risk of damaging surrounding plates/material.
IPNM10J - clamps with larger jaw opening.
IPNM10JC - Special clamp with curved jaws. Only available on request.
Features:
• Available in capacities of .5 , 1 and 2 metric tons.
• Wide variety of jaw openings available: 0 to 40mm.
• Welded alloy steel body for strength and smaller size. Forged alloy components, where required.
• Individually Proof Tested to 2 times the Working Load Limit with certification.
• User manual with test certificate is included with each clamp.
• Full 180° turning range for material transfer, turning or moving.
• Lock open, lock closed ability with latch for pretension on material and then release of material.
• There is no minimum WLL required.
• Maintenance and repair kits are available.
• All sizes are RFID EQUIPPED.
Material: Alloy steel.Marking: According to standard, CE-markedStandard: EN 13155 Warning: To be handled material must be clean and dry.
Metric Swivel Hoist Rings Crosby HR-125M
1,586.18 €*
Features:
The Working Load Limit and Recommended Torque value are permanently stamped into each washer.
Washer is color coded for easy identification: Silver - Metric thread.
Bolt specification is a Grade 12.9 Alloy socket head cap screw to DIN 912.
Designed to be used with ferrous workpiece only.
BOLT SIZE IDENTIFICATION: The size of the bolt will be stated as in the blueprint. Illustration shows meaning of each dimension given.
Safety factor: 5:1
Variants from 188.06 €*
Snatch Block McKissick 418 with Hook - Light Champion
233.49 €*
WLL:
2
The McKissick snatch block 418 Light Champion from Crosby is a snatch block fitted with a hook. Available from WLL 2 up to 15 T.
Can be delivered with bronze bushing (BB) and from WLL 8 T also with roller bearing (RB).
Features:
Bolt for opening feature is retained, to ensure no lost bolts.
Opening feature permits easy insertion of rope without reeving, or while the block is suspended.
Center pin equipped with pressure lube fitting.
All sizes feature sheave grooves suited for a range of wire line diameters.
Meets or exceeds all requirements of ASME B30.26 including identification ductility, design factor, proof load and temperature requirements.
Meet other critical performance requirements including fatigue life and material traceability, not addressed by ASME B30.26.
Material: Forged steel.Marking: CE-markedSafety factor: 4:1
Screw Clamp - IPSC10 – Ikke for løft
837.34 €*
WLL:
1.5
General:
The IPSC10 screw style clamp is suitable for use in positioning, pulling and turning steel plates and sections.
Features:
Available in capacities of 1.5 and 3 metric tons.
Jaw openings available: 0 to 60mm
Suitable for steel with a surface hardness up to 300 HV10.
Forged alloy steel body for strength and smaller size. Forged alloy components, where required.
Individually Proof Tested to 2 times the Working Load Limit with certification.
User manual with test certificate is included with each clamp.
Maintenance and repair kits are available.
Material: Alloy steel.Marking: CE-marked, Logo, WLL, serial number, proofload test date and jaw opening.Warning: Not to be used as a lifting clamp.
Shackle Crosby G-2170 Grommet
0.00 €*
WLL:
125
Features:
For use with single or double large diameter grommets.
Extra large sling contact area improves efficiency of the grommet sling.
Increases usable sling strength minimum 60 % and greatly improves life of grommet slings.
Shackles utilize new Easy-Loc bolt system.
Large machined flat on ears that can be drilled and tapped for adapting other accessories.
All 2170 shackles are individually proof tested and magnetic particle inspected.
Material: Quenched and Tempered, Cast alloy steelMarking: According to standard, CE-marked, WLL, RFID EquippedFinish: Bows are furnished Dimetcoted and pins are Dimetcoted, then painted red.Standard: EN 13889 Safety factor: 5:1
Super Terminator Wedge Socket Crosby S-423T
2,210.87 €*
Rope Ø range:
28
Wedge socket assembly with safety bolt, nut and cotter pin.
Assembly includes socket, wedge, pin, wireropeclip, tensioner bolts and secondary retention wire.
The patented wedge socket termination solution is specifically designed to be used with high performance wire ropes. The wedge socket termination gives, together with most wire ropes, a remaining strength of 80% of the wire rope's minimum breaking load. The wire rope end is secured with a wire clamp against the wedge, this prevents the wedge to come loose or be knocked out.
Features:
The 423T wedge socket terminations have a minimum efficiency rating on most high performance, high strength, compacted strand, rotation resistant wire ropes of 80% based on the catalog breaking strength of the various ropes.
Design eliminates the difficulty of properly seating the wedge with high performance wire rope into a wedge socket termination.
Proper application of the Super TERMINATOR eliminates the “first load” requirement of conventional wedge socket terminations.
Wedge and accessories provided with a zinc finish.
Basket is cast steel and individually magnetic particle inspected.
Pin diameter and jaw opening allows wedge and socket to be used in conjunction with closed swage and spelter sockets.
Secures the tail or “dead end” of the wire rope to the wedge, thus eliminates loss or “punch out” of the wedge.
Eliminates the need for an extra piece of rope, and is easily installed.
The wedge eliminates the potential breaking off of the tail due to fatigue.
The tail, which is secured by the base of the clip and the tension device, is left undeformed and available for re-use.
Material: Cast SteelMarking: According to standardStandard: EN 13411-6
Web Connector Crosby S-280
71.88 €*
WLL:
2.95
Crosby S-280 Web Connector is designed to connect synthetic web and round sling to eye hook, masterlinks or rings and standard shackles.
Material: All alloy construction.Marking: CE-markedFinish: Red painted.Safety factor: 5:1.
Vertical Lifting Clamp IPU10
568.61 €*
WLL:
0.5
The IPU10 vertical lifting clamp is used for lifting, turning, moving or vertical transfer of sheet, plates, or fabrications from horizontal to vertical and down to horizontal (180°) as needed. The hinged hoisting eye ( a.k.a. universal eye ) allows for the clamp to place and lift the load from any direction, or with a multiple leg sling without side-loading the clamp. Available in a variety of models:
IPU10 - Standard clamp for materials with a surface hardness to 363HV10 (345 HB).
IPU10J - Larger jaw opening.
IPU10S - For use with Stainless Steel material.
IPU10H - For use with materials with a surface hardness to 472HV10 (450 HB).
Features:
Available in capacities of 0.5 thru 30 metric tons
Higher Working Load Limits are available upon request.
Wide variety of jaw openings available: 0 to 155 mm.
Welded alloy steel body for strength and smaller size. Forged alloy components, where required.
Individually Proof Tested to 2 times the Working Load Limit with certification.
User manual and test certificate included with each clamp.
Full 180° turning range for material transfer, turning or moving.
Lock open, lock closed ability with latch for pretension on material and then release of material.
For use with materials with surface hardness to 279HV10, only 5% min WLL is needed.
Maintenance and repair kits are available.
All sizes are RFID EQUIPPED.
Material: Alloy steel.Marking: According to standard, CE-markedStandard: EN 13155 Warning: A minimum load of 10% of the WLL is required. Except for WLL 500 KG which requires a minimum load of 5% of WLL.
Vertical Lifting Clamp IP10(J)
450.08 €*
WLL:
0.5
The IP10 series vertical lifting clamps are used for the lifting, turning, moving or vertical transfer of sheet, plates, or fabrications from horizontal to vertical and down to horizontal (180°) as needed. Usually used as a single point pick or when used with a spreader beam with multiple vertical drop lines. Available in a variety of models:
IP10 - Standard clamp for materials with a surface hardness to 363HV10 (345 HB).
IP10J - Larger jaw opening.
IP10S - For use with Stainless Steel material.
IP10H - For use with materials with a surface hardness to 472HV10 (450 HB).
Features:
Available in capacities of .5 thru 30 metric tons
Higher Working Load Limits are available upon request.
Wide variety of jaw openings available: 0 to 155 mm.
Welded alloy steel body for strength and smaller size. Forged alloy components, where required.
Individually Proof Tested to 2 times the Working Load Limit with certification.
User manual and test certificate included with each clamp.
Full 180° turning range for material transfer, turning or moving.
Lock open, lock closed ability with latch for pretension on material and then release of material.
For plate surface hardness till 279HV10, only 5% min. WLL is needed.
Maintenance and repair kits are available.
All sizes are RFID EQUIPPED.
Material: Alloy Steel.Marking: According to standard, CE-markedStandard: EN 13155 Warning: A minimum load of 10% of the WLL is required. Except for WLL 500 kg which requires a minimum load of 5% of WLL.
Swivel Hoist Ring HR-125 UNC
185.71 €*
WLL:
1.134
Available in UNC and Metric thread sizes.
UNC threads available in sizes fom 650 pounds to 29,000 pounds Working Load Limit, with a design factor of 5 to 1.
Metric threads available in sizes from 300kg to 13,000kg and dual rated in both a 4 to 1 and 5 to 1 design factor.
360° swivel and 180° pivot action.
100% individually proof tested to 21/2 times the Working Load Limit with certification and Statistically Magnetic Particle inspected. (Can be furnished 100% Magnetic Particle inspected when requested at time of order). Bolts are individually Proof Tested.
Fatigue rated to 20,000 cycles at 11/2 times the Working Load Limit.
Bolt is secured with patented retaining ring which requires no modification to threads. This method allows for easy disassembly and assembly of hoist ring for thorough examination of all components. Replacement kits are available.
Top washer has the following features: The Working Load Limit and Recommended Torque value are permanently stamped into each washer.
Design: CrosbyFeatures: Rated at 100% at 90° angleMaterial: Alloy Steel - Quenched and TemperedMarking: Product Identification Code (PIC) for material traceability along with a working Load Limit and the name Crosby or “CG” stamped into it.Finish: Washer is colour coded for easy identification Silver Metric threadSafety factor: 5:1
Screw Pin Anchor Shackle Crosby G-209
6.46 €*
WLL:
0.5
Screw pin anchor shackles meet the performance requirements of Federal Specification RR-C-271G Type IVA, Grade A, Class 2, except for those provisions required of the contractor.
Proof load: 2 x WLL.
Material: Carbon steel with headbolt in alloy steel.Marking: According to standard, CE-markedTemperature range: -40°C up to +204°CFinish: Hot dip galvanized.Standard: EN 13889 Safety factor: 6:1Grade: 6
Open Swage Socket Crosby S-501
129.30 €*
Rope Ø range:
6
Features:
Swage sockets incorporate a reduced machined area of the shank which is the equivalent to the proper after swage dimension. Before swaging, this provides for an obvious visual difference in the shank diameter. After swaging, a uniform shank diameter is created allowing for a QUIC CHECK™ permanent visual inspection opportunity.
Designed to quickly determine whether the socket has been through the swaging operation and assist in field inspections, it does not eliminate the need to perform standard production inspections which include gauging for the proper after swage dimensions or proof loading.
Hardness controlled by spheroidise annealing.
Swage socket terminations have an efficiency rating of 100% based on the catalogue strength of wire rope.
Material: Carbon Steel.Marking: ID code and Manufacturer's symbol.Finish: Ungalvanised.Safety factor: 5:1
Alloy Screw Pin Shackle, Crosby, Wide Body S-2169
0.00 €*
WLL:
18
Capacities of 7, 12.5 and 18 metric tons.
Proof Load is 2 times the Working Load Limit.
Individually proof tested and magnetic particle inspected. Crosby certification available at time of orde.
Meets or exceeds all requirements of ASME B30.26 including identification, ductilit design factor, proof load and temperature requirements. Importantly, these shackles meet other critical performance requirements including fatigue life, impact properties and material traceability, not addressed by ASME B30.26.
Material: Quenched and Tempered for maximum strength. Forged Alloy Steel.Marking: CE-markedFinish: Self coloredSafety factor: 5:1
Shank Hook Crosby S-319BN
0.00 €*
WLL:
3.5
The most complete line of shank hoist hooks. Available 3/4 to 300 metric tons.
Proper design, careful forging, and precision controlled quench and tempering give maximum strength without excessive weight and bulk.
Material: Bronze - Quenched and TemperedSafety factor: 4:1
Open Swage Socket Talurit STTF
992.82 €*
Rope Ø range:
36
Features:
Swage sockets incorporate a reduced machined area of the shank which is the equivalent to the proper after swage dimension. Before swaging, this provides for an obvious visual difference in the shank diameter. After swaging, a uniform shank diameter is created allowing for a QUIC CHECK™ permanent visual inspection opportunity.
Designed to quickly determine whether the socket has been through the swaging operation and assist in field inspections, it does not eliminate the need to perform standard production inspections which include gauging for the proper after swage dimensions or proof loading.
Hardness controlled by spheroidise annealing.
Swage socket terminations have an efficiency rating of 100% based on the catalogue strength of wire rope.
Material: Carbon Steel.Marking: ID code and Manufacturer's symbol.Finish: Ungalvanised.Safety factor: 5:1
Variants from 167.97 €*
Open Spelter Socket McKissick G-416
87.62 €*
Rope Ø range:
10
|
WLL:
12
Standard: Fed Spec RR-S-550D TYPE A.
Features: Spelter socket terminations have an efficiency rating of 100%, based on the catalogue strength of wire rope.Material: Forged steel sockets through 11/2”, cast alloy steel 1-5/8” through 4”.Marking: ID code and Manufacturer's symbol.Finish: Galvanised.Safety factor: 5:1
Beam Clamp IPTKU
909.68 €*
WLL:
2
General:
The IPTKU series beam clamp has an improved hinged hoisting eye that increases the loading angles and an optional new “Double Locking Device”
Features:
• Available in capacities of 2 thru 10 metric tons.
• Wide variety of jaw openings available: 75 to 460 mm”.
• Welded alloy steel body for strength and smaller size. Forged alloy components, where required.
• Individually Proof Tested to 2 times the Working Load Limit with certification.
• User manual with test certificate is included with each clamp.
• Maintenance and repair kits are available.
• All sizes are RFID EQUIPPED.
Material: Alloy steel.Marking: According to standard, CE-markedStandard: EN 13155